U-Turn - 1/4-20 x 2-1/2 Full Thread Hex Tap Bolts Zinc Plated (100 Count)


U-Turn - 1/4-20 x 2-1/2 Full Thread Hex Tap Bolts Zinc Plated (100 Count)




Features
  • ITEM TYPE - Full Thread Hex Tap Bolt
  • THREAD SIZE - 1/4"-20, UNC (Coarse Thread) Class 2A
  • LENGTH - 2-1/2 inch (2-1/2")
  • MATERIAL - A307 A, Zinc Clear
  • HEX WIDTH (WRENCH SIZE) - 7/16"
  • U-Turn - 1/4-20 x 1-1/2 Stainless Steel Carriage Bolts 18-8 SS (25 Count)





    Features
  • Carriage Bolt - A rounded head bolt that most commonly features a square neck and is typically used to fast objects to wood. The square Neck allows the carriage screw to be installed without needing access to both sides of the object being fastened at the same time.
  • To install a carriage bolt, simply measure one side of the square neck of the carriage bolt, and drill a hole into the wood approximately the same diameter. Then insert the carriage bolt until the head is pressed securely against the wood. The head of the carriage bolt may need to be lighly hammered. At this point, a nut should be able to be tighted onto the threaded end, without the carriage bolt spinning in the wood.
  • Material - 18-8 Stainless Steel for good corrosion resistance
  • Thread Pitch - 1/4-20 UNC | Length - 1-1/2 inches from under the head to the tip of the threaded portion.
  • Neck Width - .245" - .260" | Head Diameter - .563" - .594" | Head Height - .125" - .145"
  • U-Turn 1/4-20 x 3-1/2 Flat Head Reamer with Wings, WAR Coated (100 Pack)





    Features
  • REAMER - Self Tapping Wood to Metal Tek Screw - ATTACHES WOOD to METAL (3/4" - 2-1/2" Wood Thickness to .110" - .375" Metal Thickness)
  • WINGS - allow screw to ream through wood before the screw reaches metal, preventing jacking action and providing smooth installation all the way through. Wings break off as they come into contact with metal.
  • DEEP CHIP CAVITY - allows screws to cut threads more effectively into metal.
  • TEK 4 DRILL POINT - gives screw a drill capacity of .110" - .375" through metal. Recommended Drill Speed is 1350 RPM.
  • W.A.R. COATED - for use in pressure treated lumber and other highly corrosive environments. These screws exceed 1000/hrs of salt spray resistance.
  • U-Turn - 1/4-20 x 2-1/2" Button Head Socket Cap Screws, 18-8 Stainless Steel, Allen Socket Drive (100 Count)





    Features
  • 100 Pack of 1/4-20 x 2-1/2" Button Head Socket Cap Screws made of pure 18-8 Stainless Steel
  • 18-8 Stainless Steel is a corrosion resistant steel consisting of 18% Chromium and 8% Nickel. This is the most common type of stainless used in fasteners due to it's low cost, corrosion resistance, and strength, as it is considered one of the stronger mild steels available.
  • Resistant to corrosion from fresh water, animal and vegetable fats, acids founds in food, and the chemicals used to clean cooking surfaces. Not recommended for use around salt water as that may cause rust over time.
  • The button head is a relatively thin, wide head that spreads the force of the screw over a large bearing area. The overall shape of the head give the screws a decorative look and makes it safer than screws with sharp edges when being used in exposed areas. The internal hex drive is great for driveability, allowing for quick, secure installation.
  • DIMENSIONS: Thread Pitch: 1/4-20 UNC | Length: 2-1/2" (2.50") | Allen Hex Socket Drive Size: 5/32" Hex | Head Diameter: 7/16" (.419" - .437") | Head Height: .122" - .132"
  • U-Turn - 1/4-20 x 2 1/2 inch Flat Head Floorboard Thread Cutting Screws, Type F, T30 Torx, Black Phosphate (400 Pack)





    Features
  • SELF TAPPING TRAILER DECK SCREWS - Designed specifically for attaching wood floors into truck trailers, but they can be used in a number of different applications such as those involving fastening to heavy gauge sheet metal, aluminum, castings, cast iron, brass, and plastic.
  • MATERIAL - Hardened Steel (RC 45 Minimum Case Hardness) | BLACK PHOSPHATE & OIL COATING - Provides corrosion Resistance
  • For consistent performance, the material in which the threads are cut should have a lower hardness of at least 10-20 Rockwell points
  • DRIVE - T-30 TORX DRIVE (6-LOBE)
  • RECOMMENDED PLATE THICKNESS - .247 inches- .253 inches | RECOMMENDED HOLE SIZE - .228 inches (#1 Drill Bit Size)
  • U-Turn - 1/4-20 x 1/2" Flat Head Socket Cap Screws 18-8 Stainless Steel, Allen Hex Drive (25 Count)





    Features
  • 25 Pack of 1/4-20 x 1/2" Flat Head Socket Cap Screws made of pure 18-8 Stainless Steel
  • 18-8 Stainless Steel is a corrosion resistant steel consisting of 18% Chromium and 8% Nickel. This is the most common type of stainless used in fasteners due to it's low cost, corrosion resistance, and strength, as it is considered one of the stronger mild steels available.
  • Resistant to corrosion from fresh water, animal and vegetable fats, acids founds in food, and the chemicals used to clean cooking surfaces. Not recommended for use around salt water as that may cause rust over time.
  • A Flat Socket Head Cap Screw has an 82 Degree Countersunk Head with an internal hex drive that is great for driveability, allowing for quick, secure installation.
  • DIMENSIONS: Thread Pitch: 1/4-20 UNC | Length: 1/2" (0.50") | Allen Hex Socket Drive Size: 5/32" Hex | Head Diameter: .480" - .531" | Head Height: .161"
  • U-Turn - 1/4-20 Coupling Nut Stainless Steel (7/8" Length) (20 Pack)





    Features
  • ITEM TYPE: Hex Coupling Nut
  • THREAD SIZE - 1/4"-20
  • LENGTH - 7/8"
  • WIDTH ACROSS THE FLATS - 3/8"
  • MATERIAL - 18-8 Stainless Steel
  • U-Turn - 1/4-20 Stainless Hex Nuts 18-8 SS (100 Count)





    Features
  • SUPERIOR QUALITY HEX NUTS made of 18-8 Stainless Steel, corrosion-resistant, which withstands the test of time without rusting in wet weather like the many zinc plated hex bolts and nuts available.
  • EASY TO USE HEXAGONAL NUTS, internally threaded, designed to be screwed with a hex wrench onto an externally threaded screw or rod with the same thread pitch and of similar material properties.
  • DEPENDABLE HARDWARE NUTS, coarse, with a thread size of 1/4"-20 UNC, with a 7/16" width across the flats and a thickness of 7/32", great for use in all types of home and industrial woodwork projects.
  • MULTIPURPOSE HEXAGON NUTS for use with anchors, bolts, screws, studs, threaded rods, easy to tighten on any fastener that has machine screw threads will create secure and long-lasting applications.
  • MONEY-SAVING HEX NUTS SETS, offered in various sizes, for all sorts of different purposes. Order this high-quality nut hardware set in a small or large size pack, at the most competitive price.
  • U-Turn - 1/4-20 x 2-1/2 Full Thread Hex Tap Bolts Zinc Plated (100 Count)





    Features
  • ITEM TYPE - Full Thread Hex Tap Bolt
  • THREAD SIZE - 1/4"-20, UNC (Coarse Thread) Class 2A
  • LENGTH - 2-1/2 inch (2-1/2")
  • MATERIAL - A307 A, Zinc Clear
  • HEX WIDTH (WRENCH SIZE) - 7/16"
  • U-Turn 1/4-20 x 3-1/4 Flat Head Reamer with Wings, 410 Stainless, Strong Shield Coated, Torx Drive (500 Pcs)





    Features
  • ATTACHES WOOD to METAL (3/4" - 2-1/4" Wood Thickness to .110" - .375" Metal Thickness)
  • WINGS - allow screw to ream through wood before the screw reaches metal, preventing jacking action and providing smooth installation all the way through. Wings break off as they come into contact with metal.
  • 410 STAINLESS STEEL, STRONG SHIELD COATED - Provides superior corrosion resistance. ACQ Compatible & Rust/Acid Rain Protection. Exceds 1,000 hr salt spray resistance.
  • TEK 4 DRILL POINT - gives screw a drill capacity of .110" - .375" through metal. Recommended Drill Speed is 1350 RPM.
  • DEEP CHIP CAVITY - allows screws to cut threads more effectively into metal.